Page 2 of 4
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Mon Nov 23, 2020 9:17 am
by fisheater
JB Weld cures hard. I repaired an exhaust manifold with it once. However, I don’t think a boot bellow would be the right place to use JB Weld. It has held on the hull of my Royalex canoe for many years. A rocky shore landing on Lake Huron in high winds and waves pounded a couple of grooves into the hull. Royalex is a laminate with layers of plastic sandwiching a foam inner layer. The outer layer had cracks that would have allowed water to infiltrate the foam layer. JB Weld has adhered and put up with years of rough use, but Royalex is quite rigid.
You need an elastic repair. I would suggest one of the two options offered.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Mon Nov 23, 2020 9:46 am
by bauerb
haha. I know that JB Weld is not right, but its the only product I have experience with...albeit for use on cars. I like the earlier suggestion of combining a soft cure epoxy with a fabric. I am thinking that if I can get a compound on the outside of the boot to bond with with a patch or something on the inside of the boot, the the "plug" might have a better chance of remaining in place. possibly as simple as a smear of compound on the inside that joins a smear on the outside through the hole.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Mon Nov 23, 2020 10:51 am
by connyro
bauerb wrote: ↑Mon Nov 23, 2020 9:46 am
possibly as simple as a smear of compound on the inside that joins a smear on the outside through the hole.
That's how I repaired the hole in my bellows with sugru. As mentioned above, jb weld is too brittle and does not bond to the bellow material.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Mon Nov 23, 2020 6:08 pm
by turnfarmer
satsuma wrote: ↑Sun Nov 22, 2020 5:22 pm
I haven't actually performed the repair, but I am a retired chemical engineer with some experience with urethanes. Urethane adhesives are generally capable of chemical reaction with residual groups on the surface of solid urethanes or Nylon, which should make them adhere better at least. Keep in mind, this is theory, I have not demonstrated.
I would suggest trying several layers of fabric (cotton or nylon), combined with a flexible, 2 part urethane adhesive such as #M DP604NS or DP640 (an Amazon reference below) , which are dispensed via a syringe kit. The adhesives have a one hour work time, so one can apply several layers at once.
Dry the surface before applying with a hair dryer or heat gun, as moisture will also react with the urethane. If you can, tape the inside of the hole first.
I think this is the best approach. Here is another urethane option that comes in single use packets and is packaged for single uses. may be easier to deal with than the dual tube one.
https://www.grainger.com/product/3KZA6? ... ccc0ba:G:s
The above linked is also the most flexible of the Hardman options.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Tue Nov 24, 2020 12:45 am
by johral
Waterproof Cordura has a Urethane backing, and is a nylon material itself. If you got like 1000D or the Balistic Nylon it might give you a good patch if you use that adhesive. Could possibly do one on the inside and one on the outside.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Tue Nov 24, 2020 10:01 am
by johral
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Tue Nov 24, 2020 10:10 am
by bauerb
how about a carbon fiber patch bonded with the flexible compound? btw, I'm pretty sure when we are done with this thread we will be able to save the space station if ever required.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Tue Nov 24, 2020 11:33 am
by johral
Carbon fiber doesn't do too well with flex. I'm not sure that would be the way to go. A carbon splinter in your foot wouldn't be so great either.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Wed Nov 25, 2020 9:16 am
by bauerb
I ordered the Sugru from Amazon. I'll have it next week.
Re: has anyone figured out a permanent fix for holes worn in boot bellows?
Posted: Mon Nov 30, 2020 11:59 am
by bauerb
received my variety pack of Sugru today. all kinds of bright colors to choose from.